Every home's wiring tells a different story, and the same is true of every commercial property. Some buildings carry decades of patchwork repairs. Others have panels that were sized for a different era and a different load. Lakewood Electrical Company works across that full range, from a single dead outlet to a complete service upgrade, serving homeowners, landlords, and commercial clients throughout Lakewood and the surrounding Los Angeles County area.
This is a straightforward choice for homeowners and property managers who need electrical work handled without the back-and-forth. You get a straight answer about the work before it is scheduled. The scope is clear, the price is confirmed, and the job moves forward when you are ready.
For homeowners and property managers alike, the range of electrical problems that come up day to day is wide. A breaker that trips repeatedly, a room that loses power, outlets that stopped working, a buzzing or warm panel, a burning smell near a switch plate. These are the faults that need attention quickly, and they are the jobs we handle on short notice. Troubleshooting starts with isolating the circuit and tracing the fault, not guessing at it. GFCI and AFCI protection is checked and tested as part of that process, because a fault that trips a breaker is sometimes a fault that a properly installed arc-fault breaker would have caught earlier.
On the installation side, we cover outlets, switches, dimmer switches, ceiling fans, recessed lighting, indoor and outdoor fixtures, security lighting, and motion sensor lighting. These are jobs that come up during renovations, after a move, or when a property is being prepared for a tenant. Commercial clients in Lakewood call for the same range of work: office and retail wiring, tenant improvement circuits, panel upgrades for commercial buildings, and repair work when a fault takes part of a property offline. We'll find the fault and fix it right.
The panel is where the whole electrical system comes together, and it is often the first place a problem shows up. A breaker that will not reset, a panel that runs warm, circuits that share a breaker they should not, or a service entrance that was never sized for today's load. Panel work covers breaker replacement and repair, full panel replacement, 100-amp to 200-amp service upgrades, subpanel installation, and meter and service entrance work. A load calculation is part of sizing a new panel correctly, because a panel that is undersized on day one will cause problems as the load grows.
Older Lakewood properties, particularly those built in the postwar decades when much of the area was developed, often carry panels that were adequate for the appliances of that era but are not adequate now. A home adding an EV charger, a hot tub circuit, or a dedicated circuit for a large appliance needs a panel that can carry the added load. Arc-fault and ground-fault breakers are part of modern panel work, and we install them where the work requires it. The wiring is done properly, start to finish.
Los Angeles County has a substantial stock of older housing, and Lakewood is no exception. Homes built in the 1940s through the 1960s often still carry knob-and-tube wiring, which was the standard of its time but was not designed for grounded circuits or the electrical loads a household draws today. Aluminum branch-circuit wiring, common in homes built in the late 1960s and into the 1970s, presents a different set of concerns at the connection points. Both are jobs we handle, from targeted remediation at specific circuits to whole-home rewiring where the scope calls for it.
Rewiring a home involves running new cable through finished walls, replacing the panel to match, and testing every circuit before the job is closed out. It is not a quick job, but the process is straightforward: the scope is set before work begins, and the work follows a clear sequence from rough-in through final test. We also handle electrical rough-in for remodels and additions, including kitchen and bathroom circuits, where the code requirements for grounding, GFCI protection, and circuit separation are specific. We find it. We fix it. We test it.
Southern California has one of the highest rates of electric vehicle ownership in the country, and the electrical work that goes with it is a regular part of what we do in Lakewood. A Level 2 home charging station requires a dedicated 240-volt circuit run from the panel to the garage or driveway location. The panel has to have the capacity to carry it, and if it does not, the panel upgrade and the charger installation are scoped together. We handle the circuit, the wiring, and the connection point.
Grid outages in Los Angeles County have become more common, and wildfire-related disruptions to power supply have made backup power a practical consideration for many households rather than an optional one. Generator hookup work covers the transfer switch installation that allows a standby generator to supply the home safely, along with the wiring between the generator and the panel. A transfer switch is what keeps a generator from back-feeding the grid, and it is a required part of any permanent hookup. Whole-home surge protection is a separate installation at the panel level, and it is worth considering alongside any panel upgrade, because the equipment a modern household runs is sensitive to voltage spikes that a panel alone does not stop. Clear communication from the first call to the final test is how that work gets done without confusion about what is covered. Give us a call and we will get the power back on.
A flickering light and a full rewire start the same way: with a clear picture of what the wiring is actually doing. An electrical safety inspection covers the panel, the branch circuits, the grounding and bonding, the condition of visible wiring, and the operation of GFCI and AFCI protection throughout the property. Inspections come up before a home purchase, after a renovation, when a property is being re-tenanted, or simply when the wiring in an older home has not been looked at in some time.
Dedicated circuits are a separate category of installation work. A clothes dryer, a refrigerator, a hot tub, or the electrical supply for an HVAC unit each needs its own circuit sized for the load. Running a dedicated circuit involves tracing a path from the panel, confirming the panel has the capacity, and making the connection at both ends. Hardwired smoke detectors and carbon monoxide detectors are part of this section of the work as well. Battery-operated units are common, but hardwired detectors with battery backup are the standard for new installation and for replacement in properties where the wiring for them already exists.
You shouldn't have to chase an electrician for answers, and you shouldn't have to wait until someone is standing in your home to find out what the work will cost. When you call about a panel upgrade, a rewiring job, an EV charger installation, or a generator hookup, the process starts with a conversation about what the job involves. The price is confirmed before anything is scheduled. You know what is covered and what the work entails before anyone comes out.
That applies to smaller jobs as well. Adding an outlet, replacing a breaker, installing a ceiling fan, or running a dedicated circuit all carry a price that can be discussed on the call. Honest recommendations on repairs, never an upsell, is the standard we work to. If a repair is the right answer, that is what we recommend. If the panel needs replacing rather than patching, we say so and explain why. A figure before anything starts. Flexible timing. Safe wiring.
We work throughout Lakewood and the communities around it across Los Angeles County. If your property is nearby, we cover it.
Communities we serve regularly include:
We are available every day from 6:00 AM to 9:30 PM. For urgent faults, calls are answered within those hours and we take short-notice work when the schedule allows. Ask what is open when you call.
This area's panels, permits, and utility rules are familiar ground. The housing stock in Lakewood includes a significant number of postwar homes, and we know what wiring conditions to expect in that era of construction. That background shapes how we scope and approach jobs before we arrive.
We work with homeowners, renters coordinating on behalf of a landlord, property managers, landlords with multi-unit buildings, and commercial clients including office and retail tenants. The process is the same regardless of who owns the property: a clear price on the call and the work done to the standard the job requires.
Call (562) 664-7998 and describe what you are seeing.
We will talk through whether it is related to the original work or a separate issue, and we will get back out to take a look. The goal is a job that holds up after we leave, and if something does not look right, that call is the right place to start.
Every job ends with a test of the circuits, outlets, fixtures, or panel work that was part of the visit. We confirm that everything is operating correctly before we close out the job, and we walk through what was done so you know exactly what changed.
Ask what the job involves, what the price covers, and whether a permit is required for the work you need. Those three questions give you a clear picture of the scope before anyone comes out. We answer all of them on the call.
Some jobs, particularly panel upgrades or rewiring projects, involve a rough-in visit and a return for final connections and testing. When that is the case, we tell you upfront so the schedule is set from the start. We do not leave a job open-ended without a clear plan for completing it.
Knowing the utility requirements, the inspection standards, and the common wiring conditions in Lakewood's housing stock means we scope jobs more accurately from the first call. A home built in the 1950s here carries different wiring considerations than a property built in the 1990s, and that affects both the plan and the price.
Yes. We clear debris from the work area, patch any access points that were opened as part of the job where that is within scope, and leave the space in the condition we found it. If a patch or finish work falls outside the electrical scope, we tell you before anything starts so you know exactly what the visit covers.
For homeowners dealing with an urgent fault, or property managers planning a panel upgrade or a rewiring project, Lakewood Electrical Company is ready to take the call. The work covers the full range of residential and commercial electrical jobs, from a single tripped breaker to a complete service upgrade, and the conversation starts the same way every time: with a clear picture of what the job involves and what it will cost.
Call (562) 664-7998 to get a quote or schedule service. Call us and the rest is handled.
(562) 664-7998