Lakewood Electrical Company handles the full range of residential and commercial electrical work in Lakewood, California, from a tripped breaker at midnight to a complete service upgrade for a growing property. Whether you need a single outlet replaced or a whole-home rewire, we scope the job on the call and show up ready to work. We are available every day from 6:00 AM to 9:30 PM.
Every job starts with a straight answer. We tell you what the work involves, what it will cost, and what to expect before anything is scheduled. A figure before anything starts. Flexible timing. Safe wiring.
Every home's wiring tells a different story, and the symptoms that bring most people to the phone are familiar ones: lights that flicker when the refrigerator kicks on, outlets that stopped working after a storm, a breaker that trips every time the microwave runs, or a section of the house that simply has no power. Each of those points to something specific, and finding it is the first part of the job.
A diagnostic visit means testing the circuit, checking the panel, and working back from the symptom to the source. We look at GFCI and AFCI protection where it applies, inspect for arc-fault and ground-fault conditions, and confirm whether the fault is at the device, the circuit, or the panel. You get a clear explanation of what we found and what fixing it involves before any work begins. We find it. We fix it. We test it.
For homeowners and property managers alike, a panel that cannot keep up with the load is a real problem. Older 100-amp services were sized for a different era. Modern homes run EV chargers, electric ranges, heat pump water heaters, and a full rack of electronics. When breakers trip frequently, when a remodel requires more circuits than the panel can carry, or when the utility flags the service entrance during an upgrade, a panel replacement is the practical answer.
We handle load calculations, subpanel installation, and service-entrance and meter upgrades. The work is done to the code inspectors in Los Angeles County enforce, and the scope is confirmed before we schedule. We'll find the fault and fix it right.
A flickering light and a full rewire start the same way: with a call to talk through what you are dealing with. Outlet and switch work is some of the most common electrical service we handle, and it covers more ground than most people expect.
Kitchens and bathrooms require GFCI protection at specific locations, and older homes often have neither. AFCI breaker installation protects bedrooms and living areas from arc-fault conditions that standard breakers do not catch. Beyond safety upgrades, we install dedicated circuits for appliances that need their own run: electric ranges, dryers, dishwashers, and refrigerators all draw enough load that sharing a circuit causes problems over time. If you are adding a circuit, replacing a switch, or upgrading a bank of outlets, we confirm what the job involves on the call and schedule from there.
You shouldn't have to chase an electrician for answers, especially when the job is something as straightforward as a lighting upgrade or a ceiling fan swap. We install recessed and LED lighting throughout the home, wire exterior fixtures for entries, garages, and driveways, and handle landscape lighting runs for pathways and outdoor spaces.
Ceiling fan installation covers wiring, box support, and confirming the circuit is rated for the load. If there is no existing box rated for a fan, we take care of that too. Outdoor lighting in Lakewood gets real use year-round, and a well-placed exterior fixture does a lot for both security and curb appeal. Call us and the rest is handled.
Whole-home rewiring is one of the larger jobs we take on, and it comes up most often in Lakewood's older housing stock where original wiring has reached the end of its service life. Aluminum wiring remediation is part of that picture in homes built during a specific stretch of the postwar era. We also handle rough-in work for additions, kitchen remodels, and bathroom remodels, running new circuits and making sure the panel has the capacity to support what is being added.
Specialty circuits are part of the wiring side too. Hot-tub circuits require a dedicated run, a disconnect, and the right GFCI protection at the panel. All of it comes down to grounding, bonding, and code-compliant wiring from start to finish.
This area's panels, permits, and utility rules are familiar ground. When we scope a wiring job in Lakewood, we already know what the inspection will look for and what the utility requires at the meter.
Residential homeowners, landlords, apartment building owners, and property managers all come to us with different needs, but the process is the same: a clear conversation on the phone, a price before we schedule, and the wiring done properly, start to finish. Whether you manage a single rental unit or a multi-unit building in Lakewood, we handle the electrical side so you can focus on everything else.
EV adoption across Los Angeles County is among the highest in the country, and Level 2 home charging has become a practical upgrade rather than a luxury. A Level 2 charger requires a dedicated 240-volt circuit and a panel with the capacity to carry it. We check panel capacity first, run the dedicated circuit, and install the charger outlet or hardwired connection. If the panel needs an upgrade to support the load, we handle that as part of the same project.
Southern California's sun exposure and utility rate structure have made solar-ready electrical work a frequent request in this area. We handle the electrical side: confirming panel readiness, running the dedicated circuits, and wiring the connection between the solar system, the battery storage unit, and the home's service. We do not install the panels or battery hardware itself, but we make sure the electrical infrastructure is in place and up to code before the equipment goes in.
Grid switching and utility fluctuations across the greater Los Angeles area can send voltage spikes through a home's circuits without warning. A panel-mounted surge protector absorbs those spikes before they reach televisions, computers, appliances, and anything else plugged into the home. Installation involves mounting the device at the main panel and confirming that grounding and bonding are solid throughout the system. It is a straightforward upgrade with a real return for electronics-heavy households.
An electrical safety inspection is a thorough look at the wiring, panel, grounding, and protection devices throughout a property. We cover arc-fault and ground-fault breaker coverage, grounding and bonding at outlets and fixtures, the condition of visible wiring, and whether the panel is properly rated for the load it carries.
Common reasons to schedule one include a home purchase, a rental property turnover, and any property with older wiring that has not been reviewed in some time. The inspection gives you a clear picture of what is working, what needs attention, and what can wait. Give us a call and we will get the power back on.
Public-safety power shutoffs during wildfire season have made generator backup a practical concern throughout Southern California, and Lakewood is no exception. We install transfer switches, wire the connection between the generator and the panel, and confirm that the hookup meets code and that the panel can handle the load.
A transfer switch is what keeps a portable or standby generator from back-feeding into the utility line, which is both a code requirement and a safety matter. We handle the full hookup: the transfer switch, the dedicated circuit, and the panel compatibility check. Honest recommendations on repairs, never an upsell, is how we approach every generator job. The scope is confirmed on the call before anything is scheduled.
We take on commercial electrical work for offices, retail spaces, and commercial buildings throughout the area. The scope covers panel capacity and load calculations for tenant buildouts, circuit installation for equipment and lighting, outdoor and interior lighting upgrades, and code-compliant wiring for new construction and tenant improvements.
Commercial properties often carry heavier electrical loads and more complex panel configurations than residential work. We scope commercial jobs the same way we handle residential: a conversation on the call, a price before we schedule, and the work done to the standard the inspectors here require.
A figure before anything starts. Flexible timing. Safe wiring.
You get the rate on the phone. When you call, we talk through what you are dealing with, give you a clear price for the work, and confirm what it covers before anything is scheduled. We are available every day from 6:00 AM to 9:30 PM, including weekends. Short-notice calls are taken when the schedule has room. Clear communication from the first call to the final test is how every job runs here.
There is no benefit to waiting on an electrical problem. A breaker that keeps tripping, an outlet with no power, or a panel that is running out of room can all get worse with time. Call for a quote and we will tell you exactly what the job involves.
We handle electrical work throughout Lakewood and the surrounding communities in Los Angeles County. The service area includes Long Beach, Bellflower, Paramount, Downey, Compton, Carson, Signal Hill, and Norwalk. Whether the job is a quick repair or a full panel upgrade, the process is the same wherever we go: scope the job on the call, give you a price, and get it done right. Call for a quote and we'll find the fault and fix it right.
A Level 2 charger requires a dedicated 240-volt circuit, and whether your panel can support it depends on the current load and available breaker slots. We check panel capacity before running the circuit, and if an upgrade is needed, we scope it as part of the same project so everything is handled in one visit.
A burning smell near an outlet or panel is a sign of overheating, which can point to a loose connection, an overloaded circuit, or deteriorating wiring insulation. It should not be ignored.
Turn off the circuit if you can identify it, and call (562) 664-7998 so we can assess the situation promptly.
We start by talking through what you are seeing and confirming the scope on the call. On site, we carry out a diagnostic, identify the fault or confirm the installation requirements, complete the work, and test everything before we leave. You get a clear explanation of what was found and what was done.
A breaker trips when a circuit draws more current than it is rated for. Occasional trips from running too many appliances at once are normal. Repeated trips on the same circuit, trips that happen without an obvious cause, or a breaker that will not reset point to a wiring fault, a failing breaker, or a panel that is undersized for the load.
An undersized or deteriorating panel limits how many circuits the home can safely run, increases the likelihood of nuisance trips, and may not support modern protection devices like AFCI breakers. In some cases, the wiring connected to an old panel has also aged in ways that create separate concerns that show up during a panel replacement.
Frequent breaker trips, no room in the panel for additional circuits, appliances that run poorly when others are on, and plans to add an EV charger or a large appliance are all signs that a 100-amp service has reached its limit. A load calculation confirms whether an upgrade is the right step.
Yes. Adding GFCI protection at kitchens, bathrooms, and outdoor locations is one of the most common upgrades we do in Lakewood's older housing stock. Grounding an ungrounded outlet requires either running a new grounded circuit from the panel or installing a GFCI outlet and labeling it correctly per code. We confirm which approach applies on the call.
Clear access to the main panel, and move furniture or stored items away from outlets, switches, and fixtures that are part of the job. If the work involves the attic or a crawl space, let us know on the call if access is limited so we can plan accordingly.
For most jobs, yes. Someone with access to the property and the panel needs to be present. If you are a property manager scheduling work at a tenant-occupied unit, we can work with whoever is on site as long as access to all the relevant areas is confirmed before we arrive.
We check the breaker condition, look for signs of overheating or corrosion at the bus bars and connections, confirm that circuits are correctly labeled, and verify that AFCI and GFCI breakers are installed where the code requires them. If the panel shows signs of wear or undersizing, we explain what we found and what the options are.
Hidden wiring, particularly in walls that have not been opened since the home was built, can add time to a job if the routing is not what we expect. Older wiring materials, including knob-and-tube or aluminum branch circuits, may require remediation rather than a simple connection. We identify these conditions during the diagnostic and adjust the scope before proceeding.
We are available every day from 6:00 AM to 9:30 PM and take short-notice calls when the schedule allows.
Call (562) 664-7998 and describe what you are dealing with.
We will tell you what is available and get you on the schedule as quickly as we can.
Lakewood Electrical Company is available every day from 6:00 AM to 9:30 PM.
Call (562) 664-7998 to get a price on any electrical job, large or small.
We find it. We fix it. We test it. Call us and the rest is handled.
Every electrical job we handle starts the same way: a conversation on the phone, a clear price, and a confirmed scope before anything is scheduled. The table below covers the full range of work we do in Lakewood and the surrounding area. Use it to find the service that fits your situation, then call for a quote and we will tell you exactly what the job involves.
| Type of Work | Scope of Work | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Wiring & Circuit Installation | New circuit runs, Rough-in for additions and remodels, Aluminum wiring remediation | Remodels, additions, and older homes where original wiring has reached the end of its service life | Aluminum branch-circuit wiring from the postwar era is common in parts of Lakewood. Remediation involves treating or replacing connections at every device and fixture on the affected circuits. |
| Electrical Safety Inspections | Panel and breaker review, Grounding and bonding check, Arc-fault and ground-fault coverage audit | Home purchases, rental property turnovers, and properties with older wiring | The inspection gives you a written picture of what is working, what needs attention, and what can wait. It is not a sales call. |
| Ceiling Fan Installation | Fan wiring, Rated box installation, Circuit load confirmation | Rooms with an existing light fixture or a new ceiling box needed | If there is no box rated for a fan already in place, we install one before the fan goes up. The circuit is confirmed for the load before we finish. |
| Electrical Repairs & Troubleshooting | Circuit diagnostics, Fault tracing, GFCI and AFCI checks, Outlet and fixture testing | Any home or property with unexplained power loss, flickering, or tripping breakers | We work from the symptom back to the source before recommending any repair, so nothing is replaced until we know what caused the problem. |
| Dedicated Appliance Circuits | Electric range and dryer circuits, Refrigerator and dishwasher runs, Workshop and garage circuits | Any appliance that draws enough load to cause problems on a shared circuit | Sharing a circuit with a high-draw appliance causes nuisance trips and can shorten the life of the appliance. A dedicated run solves both issues. |
| Lighting Installation | Recessed and LED fixtures, Exterior and security lighting, Landscape lighting runs | Homeowners upgrading interior lighting or adding outdoor coverage for security and curb appeal | Outdoor lighting in Lakewood gets year-round use. A well-placed exterior fixture adds both security and practical value without a major project. |
| Electrical Panel Upgrades | 100-amp to 200-amp service upgrades, Subpanel installation, Load calculations, Service-entrance work | Homes adding EV chargers, major appliances, or running out of breaker slots | A load calculation tells us whether an upgrade is actually needed or whether a circuit rearrangement will do the job. We confirm the scope before quoting. |
| Whole-Home Surge Protection | Panel-mounted surge device, Grounding and bonding confirmation, Protection for all circuits | Electronics-heavy households in areas with frequent grid switching or utility fluctuations | A single panel-mounted protector covers every circuit in the home. It is a straightforward upgrade that goes into service as soon as installation is complete. |
| Hot-Tub Circuits | Dedicated 240-volt circuit, Disconnect installation, GFCI protection at the panel | Homeowners installing a portable or in-ground spa | Hot-tub wiring requires a dedicated run, a weatherproof disconnect within sight of the unit, and GFCI protection. The scope is confirmed on the call before anything is scheduled. |
| Standby Battery for Outages | Electrical infrastructure prep, Dedicated circuit and panel readiness, Connection wiring for battery storage | Southern California homeowners preparing for utility shutoffs or grid instability | We handle the electrical side of battery backup: panel readiness, the dedicated circuit, and the wiring connection. Equipment selection and installation are handled by the battery supplier. |
| Breaker & Fuse Repair | Breaker replacement, Fuse panel service, Arc-fault and ground-fault breaker checks | Homes where a breaker will not reset or trips repeatedly on the same circuit | A breaker that fails to hold is sometimes a sign of a wiring fault rather than a bad breaker. We confirm the cause before swapping the part. |
| Outlet & Switch Installation | GFCI and AFCI outlet upgrades, Switch replacement, USB and specialty outlet installation | Kitchens, bathrooms, and older homes missing required protection | Lakewood's older housing stock often lacks GFCI protection at kitchens and bathrooms. Bringing those locations up to current code is one of the most common jobs we handle here. |
| EV Charger Installation | 240-volt dedicated circuit, Panel capacity check, Charger outlet or hardwired connection | Homeowners adding Level 2 charging for any electric or plug-in hybrid vehicle | EV adoption across Los Angeles County is among the highest in the country. If the panel needs an upgrade to carry the charger load, we handle that as part of the same project. |
| Older-Home Rewiring | Whole-home rewire, Knob-and-tube removal, Panel capacity review | Properties with original wiring that has not been updated since construction | A full rewire is scoped in stages. We confirm what is in the walls before committing to a method, because the routing is not always what the original plans show. |
When is it time to call an electrician instead of handling something myself?
Anything inside the panel, any work that requires opening a wall, replacing a breaker, or adding a circuit should go to an electrician. Swapping a light bulb or resetting a tripped breaker is straightforward. Replacing a breaker, adding an outlet, or tracing a fault involves live conductors and panel components where a mistake can cause a fire or a serious shock. If you are unsure whether the job is within reach, call us and describe what you are dealing with. We will tell you honestly whether it is something you can handle or whether it needs a visit.
What does it mean when lights flicker or dim when an appliance turns on?
Flickering or dimming when a large appliance kicks on usually points to a voltage drop on the circuit, which can mean the appliance is sharing a circuit it should not be on, the wiring run is undersized for the load, or the panel is struggling to deliver consistent power. It can also indicate a loose connection at the panel or at the device. We trace the symptom to the source during a diagnostic visit and confirm what the fix involves before any work starts.
What are the risks of warm or buzzing outlets?
A warm outlet or one that buzzes under load is a sign of a loose connection, an overloaded circuit, or a failing device. Heat at a connection point accelerates insulation breakdown and increases the risk of an arc. Neither symptom should be left to see if it gets better on its own. Turn off the circuit if you can identify it at the panel, and call us to schedule a diagnostic. We find the cause before recommending a fix.
Faults Traced Before Anything Is Replaced
We find the cause of a problem before we recommend a fix. That means you get honest recommendations on repairs and never a parts swap that does not address what actually went wrong.
How do I know if my home's wiring is safe to live with?
Wiring that was installed correctly and has not been disturbed or overloaded can last a long time. The concern with older wiring is not age alone but whether the materials and methods used are still compatible with how the home is actually used. Knob-and-tube wiring was not designed for grounded appliances or the loads modern households put on a circuit. Aluminum branch-circuit wiring from the 1960s and 1970s is prone to connection problems at outlets and fixtures. An electrical safety inspection gives you a clear picture of what is in the home and what, if anything, needs to be addressed.
What is involved in adding circuits for a workshop or garage?
A workshop or garage often needs more than one dedicated circuit, especially if it will run a table saw, compressor, or welder alongside standard lighting and outlets. We start with a load calculation to figure out what the panel can carry and what the new circuits need to handle. From there we run the circuits, install the outlets, and confirm that grounding and protection are in place. If the panel does not have the capacity, we scope that as part of the same project.
How does GFCI protection work and where does it need to be installed?
A GFCI device monitors the current flowing through a circuit and trips in milliseconds if it detects a ground fault, which is the kind of fault that causes electric shock near water. Code requires GFCI protection at kitchen countertop outlets, all bathroom outlets, outdoor outlets, garage outlets, and certain other locations depending on when the home was built and what updates have been made. In Lakewood's older homes, GFCI protection is often missing at one or more of those locations. We confirm what is required and what is already in place before quoting the work.
Code-Compliant Work on Every Job
The work is done to the standard the local inspectors enforce. Permit requirements are confirmed before we schedule, and the job is not considered finished until it passes.
What is the difference between a panel upgrade and a service upgrade?
A panel upgrade replaces the breaker panel itself, which adds capacity, replaces worn components, and makes room for additional circuits. A service upgrade increases the amperage coming into the home from the utility, which typically means replacing the meter base, the service entrance conductors, and the panel together. Some homes need both. We do a load calculation first to confirm what the situation actually calls for, because in some cases the panel has capacity that is not being used efficiently and a full upgrade is not necessary.
Is the electrical work permitted and inspected?
Permit requirements depend on the scope of the work and whether it falls under the jurisdiction of the city of Lakewood or Los Angeles County. Panel replacements, service upgrades, new circuit installations, and rewiring projects generally require a permit and a final inspection. We confirm what applies to your job before we schedule, and the work is done to the standard the local inspectors enforce.
Scope Agreed Before the Panel Is Opened
Clear communication from the first call to the final test is how every job runs. You get a price and a full explanation of what the work involves before anything starts.
How long does a panel upgrade typically take?
A straightforward panel replacement in a single-family home usually takes most of a day. A service upgrade that involves the meter base and service entrance conductors may take longer and requires coordination with the utility for a brief power shutoff. We confirm the timeline on the call once we know the scope, so you can plan around the work.
What backup power options can you wire for?
We handle the electrical side of generator and battery backup installations: the transfer switch, the dedicated circuit, and the panel compatibility check. A transfer switch is required to prevent the generator from back-feeding into the utility line, which is both a code requirement and a safety matter. For battery storage systems, we confirm panel readiness, run the dedicated circuit, and wire the connection between the storage unit and the home's service. We do not size or supply the generator or battery hardware, but we make sure the electrical infrastructure is in place before the equipment goes in.
How do I know if my home is ready to handle added electrical load?
The short answer is a load calculation. We add up what the panel is already carrying, account for the demand the new load will add, and compare that to the rated capacity of the service. If there is headroom, we run the circuit. If there is not, we explain what an upgrade would involve and what it would cost before anything is scheduled. This applies whether you are adding an EV charger, a hot tub, a large appliance, or a workshop circuit.
Call (562) 664-7998 and we will talk through what you are dealing with, give you a clear price, and get you on the schedule.
(562) 664-7998